Steam turbine is a common feature of all thermal power plants. Steam Turbine was invented in 1884 by Sir Charles Parsons, whose first model was connected to a dynamo that generated 7.5 kW (10 hp) of electricity. Exceptional feature of the nuclear power plant is the nuclear reactor and its safety and auxiliary systems.
Special link: 3D model of NPP – sketchfab.com
As you can see the nuclear power plant consist of two main buildings:
- Containment building (houses Nuclear Reactor)
- Turbine building (houses Turbo Generator)
The containment building is the key building of the nuclear island. It is an air-tight building, which houses a nuclear reactor and its pressurizer, reactor coolant pumps, steam generators, and other equipment or piping that might otherwise release fission products to the atmosphere in the event of an accident. Such buildings are usually made of steel-reinforced concrete.
The turbine building is the key building of the conventional (turbine) island. The turbine building houses a turbine, generator, condenser and other equipment, which is used for conversion thermal energy from pressurized steam to mechanical work used for drive the generator.
Also a cooling tower can be part of the nuclear power plant, but it is not necessary. Many nuclear power plants (coastal nuclear power plants) do not cool the cooling water via cooling towers.
Components of a nuclear power plant
The key components common to most nuclear power plants are:
- Nuclear Reactor. A nuclear reactor is a key device of nuclear power plants. Main purpose of the nuclear reactor is to initiate and control a sustained nuclear chain reaction.
- Steam Generators. Steam generators are heat exchangers used to convert feedwater into steam from heat produced in a nuclear reactor core. They are used in pressurized water reactors (PWR) between the primary and secondary coolant loops.
- Pressurizer. Pressure in the primary circuit is maintained by a pressurizer, a separate vessel that is connected to the primary circuit (hot leg) and partially filled with water which is heated to the saturation temperature (boiling point) for the desired pressure by submerged electrical heaters. Temperature in the pressurizer can be maintained at 345 °C (653 °F), which gives a subcooling margin (the difference between the pressurizer temperature and the highest temperature in the reactor core) of 30 °C.
- Reactor Coolant Pumps. Reactor coolant pumps are used to pump primary coolant around the primary circuit. These pumps are powerful, they can consume up to 6 MW each and they can be used for heating the primary coolant before a reactor start-up.
- Safety Systems. According to the U.S. Nuclear Regulatory Commission primary objectives of nuclear reactor safety systems are to shut down the reactor, maintain it in a shutdown condition and prevent the release of radioactive material. Reactor safety systems consist of:
- Reactor Protection Systems
- Essential service water system
- Emergency core cooling systems
- Emergency power systems
- Containment systems
- Steam Turbine. A steam turbine is a device that extracts thermal energy from pressurized steam and uses it to do mechanical work on a rotating output shaft.
- Generator. A generator is a device that converts mechanical energy of the steam turbine to electrical energy.
- Condenser. A condenser is a heat exchanger used to condense steam from last stage of turbine.
- Condensate-Feedwater System. Condensate-Feedwater Systems have two major functions. To supply adequate high quality water (condensate) to the steam generator and to heat the water (condensate) to a temperature close to saturation.
The heat is produced by fission in a nuclear reactor and passes into the primary cooling water. This heat, deposited in the cooling water, is conducted to the steam generators situated in the containment building. Steam generators produce high pressurized steam. The pressurized steam is then usually fed to a multi-stage steam turbine. Steam turbines in western nuclear power plants are among the largest steam turbines ever.
Manufacturing of Reactor – YoutubePressurized Water Reactor – Pressure Vessel
The Database on Nuclear Power Reactors by IAEA
The Power Reactor Information System (PRIS), developed and maintained by the IAEA for over four decades, is a comprehensive database focusing on nuclear power plants worldwide. PRIS contains information on power reactors in operation, under construction or those being decommissioned.
The database covers:
- Reactor specification data (status, location, operator, owner, suppliers, milestone dates) and technical design characteristics.
- Performance data including energy production and energy loss data, outage and operational event information.
See also: PRIS by IAEA
How Nuclear Power Plant works by UAE nuclear energy education
We hope, this article, Nuclear Power Plant, helps you. If so, give us a like in the sidebar. Main purpose of this website is to help the public to learn some interesting and important information about physics and reactor physics.